Hunter Fan Fan Ceiling Fan Light Kits User Manual

Installation Instructions  
For Hunter Ceiling Fan Light Kits  
Aurora Style  
Preparing for Installation  
CAUTIONS  
1. Unassemble the fan switch housing as shown in  
Figure 1.  
·
·
Read entire text carefully before  
beginning installation and save these  
instructions.  
2. Disconnect the upper and lower plug connectors  
between the upper switch housing and lower  
switch housing.  
Note: Do not discard any parts. You will need to  
replace it if you remove the light fixture in the  
To reduce the risk of electrical shock,  
install this light kit only on listed Hunter  
ceiling fans type A through Z.  
future.  
Upper Switch  
Housing  
WARNINGS  
·
To avoid possible electrical shock, before  
installing light fixtures, disconnect power  
by turning off the circuit breakers both  
to the outlet box and to its associated wall  
switch location. If you cannot lock the  
circuit breakers in theoff position,  
securely fasten a prominent warning  
device, such as a tag, to the service panel.  
Switch  
Housing  
Assembly  
Screws  
Lower  
Switch  
Housing  
Switch  
Housing  
Cover  
Plate  
·
·
Connect house wiring to the fan before  
attaching the light fixture to the fan.  
All wiring must be in accordance with  
national and local electrical codes. If you  
are unfamiliar with wiring, you should use  
a qualified electrician. Professional  
installation is recommended.  
Plug Button  
Switch Housing  
Assembly Screws  
Figure 1 - Unassembling the fan switch housing  
© 2003 Hunter Fan Company  
1
41558-01 3-6-2003  
 
Installing Globes and Bulbs  
Thread the fan switch pull chain through the  
grommetted hole in the light fixture bracket. Unfasten  
the extra chain looped through the hole in the in the  
lower mounting cap and attach it to the fan switch  
pull chain. Repeat for light switch pull chain.  
Refer to Figures 5, 6 and 7.  
1. Install bulbs. Use 60W Max, A-15 bulbs.  
2. Thread the fan switch pull chain through the hole in  
the metal disk.  
Hole in Lower  
Mounting Cap  
3. Place globe on pipe until flush against metal disk.  
4. Thread the light switch pull chain through the large  
center opening of the globe.  
5. Thread the fan switch pull chain through the small  
center opening in the globe.  
Figure 6 - Attaching Fan Switch Pull Chain Extension  
6. Place the cover plate up against the underside of  
the globe. Pass light and fan switch pull chains  
through the appropriate holes.  
Fan Switch  
Pull Chain  
7. Thread the light switch pull chain through the  
finial and screw the cap onto the pipe end until  
tight.  
Bulb  
Socket  
Pipe  
Metal Disk  
Globe  
Light  
Switch Pull  
Chain  
Grommetted  
Hole  
Lower Mounting Cap  
Extra Chains  
Figure 5 - Threading Fan Switch Pull Chain through  
Grommet  
Cover Plate  
Finial  
Figure 7 - Aurora Fixtures  
Hunter Fan Company  
2500 Frisco Avenue  
Memphis, Tennessee 38125  
United States of America  
© 2003 Hunter Fan Company  
3
41558-01 3-6-2003  
 

Graco Crib 8833 User Manual
Grizzly Tool Storage Tool Storage User Manual
GSW Water Heater G65 User Manual
Harman Speaker MS 10SD2 User Manual
Hearth and Home Technologies Switch WSK100 User Manual
Hotpoint Cooktop GC640 User Manual
HP Hewlett Packard Printer Volume 23 User Manual
HP Hewlett Packard Switch 1700 24 User Manual
Humminbird Fish Finder 586C HD User Manual
IBM Switch BM 8270 User Manual